Simplicity 1694498 Uživatelský manuál stáhnout pdf

How to use this file...(Operators Manuals)

————————————————————————————————————————————–––

Instructions for

Print Vendors (Paper Manuals)

Paper Size: * 11 x 17

* Body—50 lbs brilliant white offset or equivalent.

* Cover—on pre-printed two-tone “Swash” stock.

Press: * Body—1-color, 2-sided

* Cover imprint —1-color, 1-sided

Bindery:* Saddle Stitch, Face Trim

* Face Trim

COVERS:* This file may contain several manuals, which differ only in their covers.

* Covers are all present at the beginning of this file.

* Back cover for a particular manual is the page IMMEDIATELY AFTER the front cover.

• Check the front cover for the individual part number (typically a 171xxxx number).

BODY: • The body of the manual is identical, regardless of the cover used.

* REMEMBER: ODD number pages are ALWAYS right hand pages, and EVEN number are ALWAYS

left hand pages.

General: * This instruction page is NOT part of the manual and must NOT be printed.

• Pages labeled with the text “THIS PAGE INTENTIONALLY BLANK” are placement pages ONLY,

and should NOT be printed.

————————————————————————————————————————————–––

1 2 3 4 5 6 ... 19 20

Shrnutí obsahu

Strany 1 - Print Vendors (Paper Manuals)

How to use this file...(Operators Manuals)————————————————————————————————————————————–––Instructions forPrint Vendors (Paper Manuals)Paper Size: * 11

Strany 2 - THIS PAGE INTENTIONALLY BLANK

Initial Turbo Installation6Install Deflector1. See Figure 6. Drill four 13/64” holes from the bottomof the deflector at the pre-molded drill points (

Strany 3 - OPERATOR’S

Initial Turbo Installation7Install Idler Assembly & Belt Cover1. See Figure 9. Remove and discard the two taptitescrews from locations (E).2. Ins

Strany 4

Initial Turbo Installation8Install Belt Cover Plate1. Attach the belt cover plate (B, Figure 13 & 14) to thesupport bracket (E) using a 5/16-18 x

Strany 5 - Table of Contents

Initial Turbo Installation9Mower DeckArbor PulleyMower DeckTurbo Drive PulleyTurbo DrivePulleyIdlerPulleysTo SlackenBeltCAUTIONBefore you begin operat

Strany 6 - & Information

Initial Counter Balance & WeightCarrier Installation10Figure 1. Counter Balance InstallationFigure 2. Front Weight Carrier InstallationA. Washer

Strany 7 - Operating Instructions

Initial Hitch &Tube Installation11Figure 1. Install Hitch PlateA. Hitch Plate E. Upper & LowerB. Heat Shield BumperC. Capscrews, F. Washer1/2

Strany 8 - Initial Turbo

Initial Hitch & Tube Installation12Figure 4. Assemble Tubes & DeflectorAECFBA. Upper TubeB. Middle TubeC. Lower TubeD. Nut, Nylock, 10-24 x 3

Strany 9

Initial CollectorAssembly13Figure 7. Install CatcherA. Nut, #10-32 E. Hinge PinB. Handle F. BagsC. Screw, #10-32 x 1/2 G. Hair Pin ClipD. CoverFigure

Strany 10 - Initial Turbo Installation

Normal Removal &Installation14NORMAL REMOVAL & INSTALLATIONRemoving the Grass Catcher1. Disconnect the tubes (A, Figure 9) from the turbo andr

Strany 11

Removing and Reattaching Grass Catcher 15Installing the Grass Carcher1. Set the back plate & support (A, Figure 11) on pins ofhitch plate (C). Se

Strany 12

THIS PAGE INTENTIONALLY BLANK

Strany 13

16Torque Specification ChartFOR STANDARD MACHINE HARDWARE (Tolerance ± 20%)HardwareGradeSAE Grade 2 SAE Grade 5 SAE Grade 8Size Ofin/lbs in/lbsin/lbs

Strany 14 - Carrier Installation

ATTACHMENTOPERATOR’SMANUALClean Sweep Twin CatcherMfg. No. Description1694498 Clean Sweep Twin Catcher1726793Rev. 02Rev. Date 03/2004TP 100-4033-02-AT

Strany 15 - Tube Installation

Strany 16 - Assemble Catcher Bags

1Initial Collector AssemblyInstall Cover & Bags ...13Normal Removal & InstallationRemoving the Grass Catche

Strany 17 - Assembly

2Safety Rules& InformationRead these safety rules and follow them closely. Failure to obey these rules could result in loss of control ofunit, sev

Strany 18 - Normal Removal &

BEFORE OPERATIONClear the lawn of all sticks, stones, wire and other debriswhich may be caught or thrown by the mower blades.Check grass condition. If

Strany 19 - Installing the Grass Carcher

Initial TurboInstallation4 50"44"35494878645Existing Hardware(Bolt, Washer, Lockwasher, & Nut)4041424322384411239181815161781413Existing

Strany 20 - Torque Specification Chart

Initial Turbo Installation5Install Deflector Hinge Assembly1. Remove the bolts (A, Figure 2) securing the RH arborcover, then remove the cover from th

Příbuzné modely 1726793

Komentáře k této Příručce

Žádné komentáře

Simplicity 1694498 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Tiskárny Simplicity 1694498. Simplicity 1694498 User Manual Uživatelská příručka

Shrnutí obsahu

Příbuzné modely 1726793

Komentáře k této Příručce